Newer
Older
.TH "knl.conf" "5" "Slurm Configuration File" "December 2017" "Slurm Configuration File"
.SH "NAME"
knl.conf \- Slurm configuration file for Intel Knights Landing processor.
.SH "DESCRIPTION"
This ASCII file which describes configuration information for Intel Knights
Landing processors and it's name may depend upon the NodeFeatures plugin
configured in Slurm. For example, on Cray systems NodeFeatures should be configured
to "knl_cray" and its configuration file will be read from "knl_cray.conf".
The file location can be modified at system build time using the
DEFAULT_SLURM_CONF parameter or at execution time by setting the SLURM_CONF
environment variable. The file will always be located in the
same directory as the \fBslurm.conf\fP file.
This file is optional.
.LP
Parameter names are case insensitive.
Any text following a "#" in the configuration file is treated
as a comment through the end of that line.
Changes to the configuration file take effect upon restart of
Slurm daemons, daemon receipt of the SIGHUP signal, or execution
of the command "scontrol reconfigure" unless otherwise noted.
.LP
The overall configuration parameters available include:
.TP
\fBAllowMCDRAM\fR
Specify the MCDRAM modes which jobs are allowed to use.
This may be a subset of MCDRAM modes supported by the node.
If not specified, all MCDRAM modes supported by the node are available for use.
The comma separated list of allowed MCDRAM modes may include any of the modes
listed below.
.RS
.TP 17
\fBcache\fR
All of MCDRAM to be used as cache.
.TP
\fBequal\fR
MCDRAM to be used partly as cache and partly combined with primary memory.
.TP
\fBflat\fR
MCDRAM to be combined with primary memory into a "flat" memory space.
.RE
\fBAllowNUMA\fR
Specify the NUMA modes which jobs are allowed to use.
This may be a subset of NUMA modes supported by the node.
If not specified, all NUMA modes supported by the node are available for use.
The comma separated list of allowed NUMA modes may include any of the modes
listed below.
Note that Slurm can only support homogeneous nodes
(e.g. the same number of cores per NUMA node).
KNL scn4 and quad modes are not homogeneous, but each each NUMA mode will have
either 16 or 18 cores.
This will result in Slurm using the lower core count and finding a total of
256 threads rather than 272 threads and setting the node to a DOWN state.
Therefore it is recommended that snc4 and quad mode not be allowed at this time.
All to all
.TP
\fBsnc2\fR
Sub\-NUMA cluster 2
.TP
\fBsnc4\fR
Sub\-NUMA cluster 4
.TP
\fBhemi\fR
Hemisphere
.TP
\fBquad\fR
Quadrant
.RE
.TP
\fBAllowUserBoot\fR
A comma delimited list of users allowed to modify a node's MCDRAM or NUMA state.
If not specified then any user can change a node's state and reboot it.
.TP
\fBBootTime\fR
Estimated time to reboot a node in seconds.
Used as a basis for optimizing scheduling decisions.
The default value is 300 seconds (5 minutes) for the "knl_generic" plugin
and 2700 seconds (45 minutes) for the "knl_cray" plugin.
.TP
\fBCapmcPath\fR
Fully qualified path to the \fBcapmc\fR program.
The default value is "/opt/cray/capmc/default/bin/capmc".
This parameter is used only by the "knl_cray" plugin.
.TP
\fBCapmcPollFreq\fR
Time interval between when the \fBcapmc\fR program should poll for node state
changes, in seconds.
The default value is 45 seconds.
This parameter is used only by the "knl_cray" plugin.
.TP
\fBCapmcRetries\fR
Number of times to retry failed operations of the \fBcapmc\fR program.
Default value is 4.
.TP
\fBCapmcTimeout\fR
Time limit for the \fBcapmc\fR program to return status information milliseconds.
The default value is 60000 milliseconds and the minimum value is 1000 milliseconds.
This parameter is used by the "knl_cray" plugin, plus the capmc_suspend and
capmc_resume programs used for suspending and resuming nodes.
.TP
\fBCnselectPath\fR
Fully qualified path to the \fBcnselect\fR program.
The default value is "/opt/cray/sdb/default/bin/cnselect".
This parameter is used only by the "knl_cray" plugin.
.TP
\fBDefaultMCDRAM\fR
Specify the default MCDRAM modes for job's which do not specify a value.
This is only used when a node is booted and the job which has been allocated
the node does not specify a desired MCDRAM mode.
The value can include one of the possible values identified with the
\fBAllowMCDRAM\fR configuration parameter above.
The default value is "cache".
.TP
\fBDefaultNUMA\fR
Specify the default NUMA modes for job's which do not specify a value.
This is only used when a node is booted and the job which has been allocated
the node does not specify a desired NUMA mode.
The value can include one of the possible values identified with the
\fBAllowNUMA\fR configuration parameter above.
The default value is "a2a".
.TP
\fBForce\fR
If set to a non\-zero value then load the node_features/generic plugin even
on non\-KNL nodes.
Used primarily for testing purposes.
.TP
\fBLogFile\fR
Fully qualified path to a log file.
The default value is SlurmctldLogFile from the slurm.conf configuration file.
This is option is used only by the campc_suspend and campc_resume programs
(which power down and reboot nodes in the appropriate configuration).
.TP
\fBMcPath\fR
Fully qualified path to memory controller device file directory.
Children of this directory with names of the form "mc#/csrow#/ue_count"
(i.e. the count of unrecoverable memory errors) will be monitored for non\-zero
values.
If such errors are detected, the node will be set to a DOWN state and the
slurmd daemon will shutdown.
The default value is "/sys/devices/system/edac/mc".
See also \fBUmeCheckInterval\fR.
.TP
\fBSyscfgPath\fR
Fully qualified path to Intel's \fBsyscfg\fR program, which identifies current
KNL configuration by viewing BIOS settings.
If not defined, the current BIOS setting will not be available.
This parameter is used only by the "knl_generic" plugin.
.TP
\fBSyscfgTimeout\fR
Timeout for \fBsyscfg\fR program in milliseconds.
Default value is 1000 milliseconds.
For Dell KNL systems, experience has shown that a higher value of 10000
milliseconds is more appropriate.
Danny Auble
committed
.TP
\fBSystemType\fR
Used to distinguish the flavor of knl we are dealing with.
Possible options are "Dell" and "Intel".
The default value is "Intel".
This parameter is used only by the "knl_generic" plugin.
.TP
\fBUmeCheckInterval\fR
Interval, in microseconds, between checks for Uncorrectable Memory Errors (UME).
If such errors are detected, the node will be set to a DOWN state and the
slurmd daemon will shutdown.
The default value is 0 (disabled).
See also \fBMcPath\fR.
###################################################################
.br
# knl_cray.conf
# Slurm configuration file for Intel Knights Landing on Cray system
###################################################################
CapmcPath=/opt/cray/capmc/default/bin/capmc
.br
LogFile=/var/tmp/slurm_node_feature.log
Copyright (C) 2015-2017 SchedMD LLC.
.LP
This file is part of Slurm, a resource management program.
For details, see <https://slurm.schedmd.com/>.
.LP
Slurm is free software; you can redistribute it and/or modify it under
the terms of the GNU General Public License as published by the Free
Software Foundation; either version 2 of the License, or (at your option)
any later version.
.LP
Slurm is distributed in the hope that it will be useful, but WITHOUT ANY
WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS
FOR A PARTICULAR PURPOSE. See the GNU General Public License for more
details.
.SH "SEE ALSO"
.LP
\fBslurm.conf\fR(5)